Best Chengde transformer quotation

2022-07-26
  • Detail

Chengde transformer quotation

AC contactor is a kind of contactor. Its typical structure is divided into double break point direct acting type (lc1-d/f*) and single break rotating type (lc1-b*). Later, the iron core of the transformer was made of e-type iron sheets, which was put into commercial use in 1886. Since the suction coil of the DC contactor is connected with DC, there is no impact starting current and there will be no violent impact of the iron core. Therefore, it has a long service life and is suitable for frequent startup and shutdown. For AC contactor, the reason can be found from the above four aspects to solve the problem that the current of the main contact connection circuit is AC. If the load is too heavy, the selected motor and frequency converter cannot drag the load, which may also be caused by poor mechanical lubrication

the contactor adopts modular design, which can assemble the number of contact paths required by the customer and the contact forms required by the customer (normally open, normally closed and conversion) with the least parts; The contact breaking voltage of this series of products is high, and the quotation of Chengde transformer_ Raocheng electric appliance - cloud express screen control system, with horizontal blowing magnetic field for arc extinguishing, and the maximum breaking voltage can reach 220vdc The product is applicable to the quotation of programmable power supply or uninterruptible power supply system, forklift and Chengde transformer_ Raocheng electric appliance - cloud express PA screen system, electric vehicle, engineering machinery system

selection of operating frequency 6) loading refers to the number of on-off times of the contactor per hour When the on-off current is large and the on-off frequency is too high, the contact will be seriously overheated and even fused If the operating frequency exceeds the specified value, the DC contactor with a higher rated current shall be selected

transformer is a device that uses the principle of electromagnetic induction to change AC voltage. Its main components are primary coil, secondary coil and iron core (magnetic core). The main functions are: voltage transformation, current transformation, impedance transformation, isolation, voltage stabilization (magnetic saturation transformer), etc. It can be divided into: power transformer and special transformer (electric furnace transformer, rectifier transformer, power frequency test transformer, voltage regulator, mining transformer, audio transformer, intermediate frequency transformer, high frequency transformer, impulse transformer, instrument transformer, electronic transformer, reactor, mutual inductor, etc.) according to the purpose. Circuit symbols often begin with T Example: T01, t201, etc

AC contactor is a kind of contactor. Chengde transformer quotation_ The typical structure of Raocheng electric appliance cloud express screen control system is divided into two breakpoint direct acting type (lc1-d/f*) and single break rotating type (lc1-b*). Combination of AC contactor and relay control circuit, remote control or interlocking of relevant electrical equipment. At present, the most commonly used products are CJX2 series, cj20 series, cjt1 series 3TB, B series, etc. of CJ series

the connecting rod connected with the armature drives the contact to act, so that the normally closed contact breaker is in the energized state; When the suction coil is powered off, the electromagnetic force disappears, the armature is reopened, the normally open contact is closed, the position spring is released, all contacts are reset, and the contactor is in the power-off state

proximity switch is a position switch that can be operated without direct mechanical contact with moving parts. When an object approaches the sensing surface of the switch to the action distance, the switch can be operated without mechanical contact and any pressure, so as to drive DC appliances or provide control instructions to computer (PLC) devices. Proximity switch is a kind of switch type sensor. The current H3PO4 iron Li material is limited by the theoretical specific capacity and can not meet the requirements of 2020 (i.e. contactless switch). It has the characteristics of travel switch and microswitch, and has sensing performance. It has reliable action, stable performance, fast frequency response, long service life, strong anti-interference ability, waterproof, shockproof, corrosion-resistant and other characteristics. The products are inductance type, capacitance type, hall type, AC and DC type

schematic circuit diagram of current transformer similar to transformer, micro current transformer also works according to the principle of electromagnetic induction. Transformer transformation 3 The third generation semiconductor Innovation Incubation Platform is built by voltage, while the micro current transformer transforms current. Winding N1 is connected to the measured current, which is called primary winding (or primary winding, primary winding); Winding N2 is connected to the measuring instrument, which is called secondary winding (or secondary side winding, secondary winding)

the current ratio between the primary winding current I1 and the secondary winding I2 of the micro current transformer is called the actual current ratio K. The current ratio of the miniature current transformer working under the rated working current is called the rated current ratio of the current transformer, which is expressed in kn. kn=i1n/i2n

Copyright © 2011 JIN SHI